{"product_id":"mercury-harness-adapter-non-dts-14-pin-female-to-8-pin-male-8-ft-fits-2006-and-newer-non-dts-outboards-from-25-hp-to-250-hp-14-pin-connectors-84-896539t08","title":"Mercury – Ignition Harness Adapter Non DTS 14 Pin Female to 8 Pin Male | 84-896539T08","description":"\u003ch2\u003eMercury – Ignition Harness Adapter Non-DTS 14-Pin Female to 8-Pin Male | 84-896539T08\u003cbr\u003e\u003cbr\u003e\n\u003c\/h2\u003e\n\u003cp\u003eThe Mercury Non-DTS Ignition Harness Adapter is designed for mechanical control setups where a fourteen-pin boat-side harness must connect to an eight-pin engine ignition port. It is most commonly used during repowers or engine upgrades when the existing boat wiring remains in place but the engine connector style differs. This adapter allows the two systems to interface correctly without modifying the main harness, helping maintain a clean, factory-style installation.\u003c\/p\u003e\n\u003cp\u003eMaintaining proper connector compatibility supports consistent ignition signal flow and helps reduce stress on wiring and terminals caused by mismatched connections. Proper mounting, secure routing, and routine inspection help ensure dependable starting behavior and long-term electrical reliability in typical marine environments.\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e14-Pin Female to 8-Pin Male Adapter\u003c\/strong\u003e – Bridges boat harnesses to legacy engine ignition connectors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNon-DTS Mechanical Design\u003c\/strong\u003e – Intended for traditional control systems without digital throttle and shift\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Bracket \u0026amp; Hardware Included\u003c\/strong\u003e – Helps secure and protect the adapter during operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMarine-Grade Electrical Construction\u003c\/strong\u003e – Built to withstand vibration, moisture, and engine-compartment heat\u003cbr\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eEngine \u0026amp; System Compatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMercury outboards\u003c\/li\u003e\n\u003cli\u003eMechanical remote control systems\u003c\/li\u003e\n\u003cli\u003eECM-equipped engines\u003c\/li\u003e\n\u003cli\u003eNon-DTS outboards from 25 HP to 250 HP\u003cbr\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant Notes\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eConfirm boat harness connector type and engine ignition port configuration before ordering\u003c\/li\u003e\n\u003cli\u003eSecure the adapter using the included mounting hardware\u003c\/li\u003e\n\u003cli\u003eEnsure all connections are fully seated during installation\u003c\/li\u003e\n\u003cli\u003eVerify proper ignition operation after installation\u003cbr\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1) What is this ignition harness adapter used for?\u003c\/strong\u003e\u003cbr\u003eIt allows a fourteen-pin boat-side ignition harness to connect to an eight-pin engine ignition port.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e2) When is this adapter typically required?\u003c\/strong\u003e\u003cbr\u003eIt is commonly needed during repowers or engine upgrades when the engine uses a different ignition connector style than the existing boat harness.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3) Is this adapter compatible with DTS systems?\u003c\/strong\u003e\u003cbr\u003eNo. This adapter is intended for non-DTS mechanical ignition systems only.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e4) Does this adapter eliminate the need to replace the full ignition harness?\u003c\/strong\u003e\u003cbr\u003eYes. It allows proper connection without modifying or replacing the main boat-side harness.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e5) Why choose an OEM Mercury ignition adapter?\u003c\/strong\u003e\u003cbr\u003eOEM adapters are built to Mercury electrical specifications, helping ensure clean signal communication, reliable starting, and long-term durability.\u003c\/p\u003e","brand":"Mercury","offers":[{"title":"Default Title","offer_id":46936026284323,"sku":"84-896539T08","price":87.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0783\/7410\/9475\/files\/896539t_2.jpg?v=1698795828","url":"https:\/\/partsvu.com\/en-ca\/products\/mercury-harness-adapter-non-dts-14-pin-female-to-8-pin-male-8-ft-fits-2006-and-newer-non-dts-outboards-from-25-hp-to-250-hp-14-pin-connectors-84-896539t08","provider":"PartsVu","version":"1.0","type":"link"}