Suzuki Outboard Spark Plugs & Ignition Components

Suzuki Outboard Spark Plugs & Ignition Components FAQ

How do I perform a leakdown test on my Suzuki outboard engine?

1. Step #1: Begin by carefully removing the top Suzuki cowling, Then, remove the ignition coil cover at the rear of the motor.
2. Step #2: Remove the spark plugs. Be sure to lay the spark plugs in numbered order to reinsert or replace them after the test.
3. Step #3: Remove the flywheel cover from the top of the motor.
4. Step #4: Mark the flywheel with a marker at 0°, 120°, and 240°. These positions will indicate where you’ll rotate each pair of cylinders to the top-dead-center positions (see Steps #11 and #12 below).
5. Step #5: Rotate the crankshaft with your ratchet and socket to the top dead center for Suzuki Suzuki cylinder #1.
6. Step #6: Adjust the regulator on the leak down tester to 0% to calibrate it for an accurate reading.
7. Step #7: Connect the leak-down tester by screwing it into the spark plug port at cylinder #1. Next, connect the tester to the compressor and take a measurement. Be sure to firmly hold the crankshaft to prevent it from rotating.
8. Step #8: Rotate the crankshaft 360° (one full rotation) to put Suzuki cylinder #4 at the top dead center.
9. Step #9: Connect the leak-down tester to cylinder #4. Then, take a measurement while holding the crankshaft to prevent it from rotating.
10. Step #10: Set Suzuki cylinder #3 to the top dead center at the 120° mark. Next, repeat step #7 through Step #10 for Suzuki cylinders #3 and #6.
11. Step #11: Set cylinder #2 to the top dead center at the 240° mark. Then, repeat step #7 through Step #10 for Suzuki cylinders #2 and #5.

Step #12: Replacement is the same as disassembly. Be sure to replace spark plugs in numbered order and apply an anti-seizing lubricant on the threads for easy removal/replacement in the future. Also, firmly reattach the ignition wires for a solid connection.

How do I know if I have water in my Suzuki outboard engine block?

If you are confronted with water in your Suzuki outboard engine, the first place to look before disassembling the engine and checking for a porous Suzuki outboard engine block, cracked Suzuki cylinder head, eroded exhaust-water passage, frozen oil cooler, or other labor-intensive issues, is the Suzuki thermostat. Remember that some engines have two thermostats, like Suzuki’s V-engines.

To locate the Suzuki thermostat(s), be sure to refer to the service manual as the location varies by the engine. The service manual procedure states that you should put the thermostat in a pot of hot water and check if it opens and closes at the correct temperature. If you do not have access to this method, then an infrared temperature gun can be used at the thermostat housing to get an indication of engine temperature. Again, refer to the service manual for the correct temperature operating range.

If you’ve determined that the engine is running cold, it’s a good indicator that the thermostat is stuck open. Remove the thermostat housing and inspect it. If it is stuck open, replace the thermostat with a new one, and be sure to do several oil and filter changes to ensure water is removed from the engine’s oil.

You might be wondering how water gets into the oil due to a thermostat being stuck open. If the engine is running cold, the hot oil meeting a cold engine can produce condensation. The condensation eventually condenses into water and falls into the oil. With an engine running cold, water isn’t the only pollutant getting into the oil. The piston rings (running cold) won’t fully expand to thoroughly seal against the Suzuki outboard cylinder wall and may allow a small percentage of raw fuel to constantly seep past them and collect in the sump. Prolonged running with this condition can cause the oil to develop a milky residue. Debris can also get stuck in thermostats and prevent them from retracting back to the closed position.

If you suspect water in the engine oil, there are a couple of quick ways to check. One way is to remove and look at the underside of the oil cap to see if there’s moisture in it. Another way is to pull out the dipstick to check for moisture in the oil. Either method is effective. Suzuki thermostat issues can be prevented by flushing the engine regularly per the owner’s manual.

How do I start a flooded Suzuki outboard motor?

What causes a flooded Suzuki outboard engine, and what does it mean?

A flooded motor has too much fuel in the cylinder, and it can therefore be very difficult– or impossible– to start. A strong smell of gasoline may indicate that this has occurred.

Even if your motor does start while flooded, it’s important to address it immediately anyway. Running a flooded motor can damage the whole system, leading to a much larger (and more expensive) set of problems.

Now, to address the problem: wait about five minutes before you clear-flood start the engine. You do this by moving the throttle to the clear-throttle or wide-open throttle position and crank your engine. This allows air to enter the engine, but not fuel, and should get things moving along. It may take a few tries for this to be effective.

Why did my Suzuki outboard motor stop working?

Your Suzuki outboard ignition system is responsible for firing up the engine and keeping it running. Because checking this system may involve sparks and heat, keep flammable liquids away.

The first part of the ignition system to check is the spark plugs. Clean and adjust the spark plugs– they may need to be replaced. Check the ignition spark with a spark gap tester. If you’ve got a good spark, make sure that the air gap is within specification. Adjust it if needed.

If you have a good spark and the gap is within specification, the problem will likely not be found in the ignition system.

However, if you don’t have a good spark, salt buildup on the spark plug caps or ignition coil leads could be causing problems. You’ll also need to check both the spark plug caps and ignition coil leads for proper resistance. Replace degraded parts. When there is no salt buildup and both parts have proper resistance, check the ECM output peak voltage.

If your spark plugs don’t seem to be the issue, check that the electric oil pump and oil level sensor are in good condition. If so, check the reed valve for its condition.

How do I perform a 100-hour service on my Suzuki outboard engine?

To ensure proper engine function, it’s always best to service your Suzuki outboard engine every 100 hours after the initial break-in period (first 10 hours) and after the first maintenance interval (at 20 hours).

The following is a Suzuki 100-hour service checklist to help you service your engine properly:

If you want a more in-depth explanation of how to perform a 100-hour service on a Suzuki outboard engine, read our blog “Suzuki Outboard 100-Hour Service Checklist”. Also, be sure to refer to your Suzuki Outboard Service Manual for which parts you’ll need, how to perform basic repairs, and other engine specific tasks

To make engine maintenance even easier, PartsVu has a wide selection of Suzuki outboard engine 100-hour service kits available. They’re pre-assembled with everything you need to keep your boat happy and healthy every 100 hours.

Having trouble starting your engine up or experiencing an inconsistent performance at all RPMs? If so, make sure your Suzuki outboard engine starts up every time by replacing your old Suzuki Outboard Spark Plugs & Ignition Components on a regular basis with certified Suzuki OEM replacement parts.